FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups 
 ProfileProfile   PreferencesPreferences   Log in to check your private messagesLog in to check your private messages   Log inLog in 
Forum index » Electronix » Repair
Scantronix 9827 alarm system - help needed
Post new topic   Reply to topic Page 1 of 1 [2 Posts] View previous topic :: View next topic
Author Message
Tim Ellison
electronics forum beginner


Joined: 07 Jul 2006
Posts: 2

PostPosted: Fri Jul 07, 2006 11:32 am    Post subject: Scantronix 9827 alarm system - help needed Reply with quote

Hi. I have a house alarm system that utilises a Scantronic 9827 control
panel. I have tried to omit a PIR using "code, then zone, then X PIR
NUMBER" as per the user manual but it doesn't work. After reading the
manual again, it does suggest that the installer needs to program any
PIR to be 'omittable' before I can omit it!

I've just had the installer out to reprogram the zones last week, and
I'm slightly embarrased to have to ask him to come out again and
re-program it again!

Does anyone out there have an installer manual (or can tell me how to
do it) so I can omit PIR number 5. (It's the room where I put my dog
when I go out, and she keeps setting the alarm off)! I only want to
omit the PIR on occasion, and the user manual tells me that this is a
temporary thing which only lasts for a single setting/disabling cycle,
which is exactly what I want!

Any help anyone could give me would be very much appreciated.

Thanks in advance!




--
Tim Ellison
Back to top
Tim Ellison
electronics forum beginner


Joined: 07 Jul 2006
Posts: 2

PostPosted: Thu Jul 20, 2006 5:24 pm    Post subject: Re: Scantronix 9827 alarm system - help needed Reply with quote

Tim Ellison Wrote:
Quote:
Hi. I have a house alarm system that utilises a Scantronic 9827 control
panel. I have tried to omit a PIR using "code, then zone, then X PIR
NUMBER" as per the user manual but it doesn't work. After reading the
manual again, it does suggest that the installer needs to program any
PIR to be 'omittable' before I can omit it!

I've just had the installer out to reprogram the zones last week, and
I'm slightly embarrased to have to ask him to come out again and
re-program it again!

Does anyone out there have an installer manual (or can tell me how to
do it) so I can omit PIR number 5. (It's the room where I put my dog
when I go out, and she keeps setting the alarm off)! I only want to
omit the PIR on occasion, and the user manual tells me that this is a
temporary thing which only lasts for a single setting/disabling cycle,
which is exactly what I want!

Any help anyone could give me would be very much appreciated.

Thanks in advance!


Hi again. Can anyone help me or point me in the right direction with
this one?




--
Tim Ellison
Back to top
Google

Back to top
Display posts from previous:   
Post new topic   Reply to topic Page 1 of 1 [2 Posts] View previous topic :: View next topic
The time now is Mon Aug 21, 2017 5:51 pm | All times are GMT
Forum index » Electronix » Repair
Jump to:  

Similar Topics
Topic Author Forum Replies Last Post
No new posts Pressure Transducer Linear algorithm needed William Hightower design 7 Tue Jul 18, 2006 12:24 pm
No new posts Strategic Partnership Initiative for Solving Multi-Physic... support@polyteda.com cad 0 Mon Jul 17, 2006 3:30 pm
No new posts 12V DC to 1.5V DC needed 3T39 Repair 11 Fri Jul 14, 2006 10:02 pm
No new posts KLH 21 Tuning Cap needed Tim Schwartz Repair 1 Fri Jul 14, 2006 7:42 pm
No new posts Fictional "Intercom System" Over City Power Lines phaeton Basics 11 Wed Jul 12, 2006 4:13 pm

Copyright © 2004-2005 DeniX Solutions SRL
Other DeniX Solutions sites: Unix/Linux blog |  Unix/Linux documentation |  Unix/Linux forums |  Medicine forum |  Science forum  |  Send and track newsletters


Powered by phpBB © 2001, 2005 phpBB Group