FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups 
 ProfileProfile   PreferencesPreferences   Log in to check your private messagesLog in to check your private messages   Log inLog in 
Forum index » Electronix » Repair
JVC av56wp30 56" TV, no red convergence control
Post new topic   Reply to topic Page 1 of 1 [9 Posts] View previous topic :: View next topic
Author Message
BigMike
electronics forum beginner


Joined: 29 Dec 2005
Posts: 11

PostPosted: Thu Dec 29, 2005 11:01 pm    Post subject: JVC av56wp30 56" TV, no red convergence control Reply with quote

I have a customers set in the shop, that the red convergence is way off,
and the on screen convergence settings will let me move the red from side
to side, but the up-down controls don't work at all. I am guessing a chip
or other component in the convergence circuit has popped. Anynbody seen
this in this model? Thank you much...

Mike Shullaw
Lee's TV
Lincoln Ne.
Back to top
stokesb@cox.net
electronics forum addict


Joined: 16 Sep 2005
Posts: 79

PostPosted: Fri Dec 30, 2005 2:49 am    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

Mike, I am not a Pro, but I had the same problem with a 50" Hitachi,
but it was the blue that wouldn't move. I had to replace the
convergence amp. This fixed this problem. Hope this helps.
Back to top
Dani
electronics forum Guru Wannabe


Joined: 18 Dec 2005
Posts: 137

PostPosted: Fri Dec 30, 2005 3:24 am    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

Replace both STK convergence IC's, also check low value resistors.
..5, or 1.0 ohms approx.


"BigMike" <bigmikey@alltel.net> wrote in message
news:op.s2kh9kry87sx8z@bigmike-3u89k6k...
Quote:
I have a customers set in the shop, that the red convergence is way off,
and the on screen convergence settings will let me move the red from side
to side, but the up-down controls don't work at all. I am guessing a chip
or other component in the convergence circuit has popped. Anynbody seen
this in this model? Thank you much...

Mike Shullaw
Lee's TV
Lincoln Ne.
Back to top
BigMike
electronics forum beginner


Joined: 29 Dec 2005
Posts: 11

PostPosted: Fri Dec 30, 2005 4:46 pm    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

On Thu, 29 Dec 2005 21:36:53 -0600, Dani <greeben@gmail.com> wrote:

Quote:
Replace both STK convergence IC's, also check low value resistors.
.5, or 1.0 ohms ap


Thanks for the tip, I appreciate it. "Because of the interlock on the back
on this JVC, I don't wan't to take the back off until I have the parts.
Seems this is a very common problem with this set, so I am going to try to
find the part numbers and get them on order first. I'm just glad I knew
about the booby trap on the back, or this could of been a real pain.






--
Using Opera's revolutionary e-mail client: http://www.opera.com/mail/
Back to top
BigMike
electronics forum beginner


Joined: 29 Dec 2005
Posts: 11

PostPosted: Fri Dec 30, 2005 4:47 pm    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

On Thu, 29 Dec 2005 20:49:02 -0600, Golf <stokesb@cox.net> wrote:

Quote:
Mike, I am not a Pro, but I had the same problem with a 50" Hitachi,
but it was the blue that wouldn't move. I had to replace the
convergence amp. This fixed this problem. Hope this helps.



Thanks for the tip!
Back to top
John-Del
electronics forum Guru Wannabe


Joined: 29 Apr 2005
Posts: 107

PostPosted: Fri Dec 30, 2005 11:35 pm    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

You can do the convergence surgery through the front panel of this
model without removing the back and setting off the booby trap.

John
Back to top
Jason D.
electronics forum Guru Wannabe


Joined: 06 May 2005
Posts: 196

PostPosted: Sat Dec 31, 2005 1:44 am    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

On Fri, 30 Dec 2005 10:46:33 -0600, BigMike <bigmikey@alltel.net>
wrote:

Quote:
On Thu, 29 Dec 2005 21:36:53 -0600, Dani <greeben@gmail.com> wrote:

Replace both STK convergence IC's, also check low value resistors.
.5, or 1.0 ohms ap


Thanks for the tip, I appreciate it. "Because of the interlock on the back
on this JVC, I don't wan't to take the back off until I have the parts.
Seems this is a very common problem with this set, so I am going to try to
find the part numbers and get them on order first. I'm just glad I knew
about the booby trap on the back, or this could of been a real pain.



Good you're aware of it.

The booby trap is the optical sensor under a hole in the DVI metal
box. Unplug power plug and wait a minute, remove panel, unplug all
wires to the DVI module and you can work on it safely with power on.

Also you can work from front for convergence job only, if this model
uses long retangular convergence board (no screws, held in place with
snap hooks with metal box. you can get it out from front and reach
deep to release one of cables from holders and unplug from the small
stand up PCB.

I did this on several of those.

Cheers, Wizard
Back to top
BigMike
electronics forum beginner


Joined: 29 Dec 2005
Posts: 11

PostPosted: Wed Jan 04, 2006 2:51 am    Post subject: Re: JVC av56wp30 56" TV, no red convergence control Reply with quote

On Fri, 30 Dec 2005 17:35:02 -0600, John-Del <ohger1s@aol.com> wrote:

Quote:

You can do the convergence surgery through the front panel of this
model without removing the back and setting off the booby trap.

John


Thanks for the tip, John. I replaced the ICs and one burnt out resistor,
and the set is working fine. I have a question about it. After I replaced
the ICs, the auto convergence pulled the center together real well, but I
had to manually adjust the outsides of the screen, which were pretty far
off. Also, the heatsinks on the ICs are running pretty darn hot, although
the ICs themselfs seem to be only warm, I can leave my finger on them.
Should these heatsinks run hot, and is the outside convergence needing to
be manually aligned, normal? Or should I be on the lookout for something
else? Thanks for the help...




--
Using Opera's revolutionary e-mail client: http://www.opera.com/mail/
Back to top
mikegl71
electronics forum beginner


Joined: 17 Sep 2006
Posts: 1

PostPosted: Sun Sep 17, 2006 10:59 pm    Post subject: Replacing STK392-110 didn't work Reply with quote

I have the same problem with my JVC. The red will converge up and down, but not left to right. I replaced both STK392-110 chips, but the problem is the same.

Any suggestions?
Back to top
Google

Back to top
Display posts from previous:   
Post new topic   Reply to topic Page 1 of 1 [9 Posts] View previous topic :: View next topic
The time now is Thu Oct 19, 2017 3:46 am | All times are GMT
Forum index » Electronix » Repair
Jump to:  

Similar Topics
Topic Author Forum Replies Last Post
No new posts How can control RPM of DC Motor nuiseng191 Basics 2 Wed Apr 11, 2007 4:24 pm
No new posts RCA F25432 Convergence mperry43@gmail.com Repair 2 Sat Jul 15, 2006 3:32 pm
No new posts Ideas for Smart SCR Control Board Paul E. Schoen design 7 Wed Jul 12, 2006 8:13 am
No new posts Three phase sine wave amplitude control PK design 3 Tue Jul 11, 2006 6:32 am
No new posts Small Pocket Computer For Data Logging And Control Too_Many_Tools design 26 Mon Jul 10, 2006 3:55 am

Copyright © 2004-2005 DeniX Solutions SRL
Other DeniX Solutions sites: Unix/Linux blog |  Unix/Linux documentation |  Unix/Linux forums |  Medicine forum |  Science forum  |  Send and track newsletters


Powered by phpBB © 2001, 2005 phpBB Group